[openob-users] Re: Prerequisites

Richard, Thanks very much for your crib sheet. It worked just fine for me and I am now up and running. Now I have my own notes to help me if I ever have to do this again! Ted, I see your point. This is a huge hole if it goes over the internet. I was debating running this STL over a VPN tunnel. You have swung me over and I will definitely do so after hearing about the redis security issues. Thanks very much for alerting me to this. Thanks again guys! Phil *From:*Richard Graham [mailto:richard.graham@markfourmedia.co.uk] *Sent:* Thursday, July 16, 2020 5:36 AM *To:* openob-users(a)lists.talkunafraid.co.uk *Subject:* [openob-users] Re: Prerequisites Is this the correct version of g-streamer? Below is a copy of a ‘crib-sheet’ that I put together for putting a Pi together for using OpenOB – this is using a Pi 3 not a 4 though and the ‘Audio Injector’ hat – but the OOB installation should be the same. This uses the April 2019 version of Raspbian, and the OpenOB version available in August 2019. --- Install the prerequisites for OpenOB plus a couple other bits that are needed: sudo apt install gstreamer1.0-plugins-base gstreamer1.0-plugins-good gir1.2-gstreamer-1.0 python-gst-1.0 python-redis python-gi python-setuptools gstreamer1.0-alsa python-pip screen Install redis-server on the receiver: sudo apt install redis-server and configure: sudo sed -i.bak 's/bind 127.*/bind 0.0.0.0/' /etc/redis/redis.conf && sudo service redis-server restart Install OpenOB: sudo pip install openob --- For a previous build, I did at some point find a repository that had older versions of gstreamer in it and use it that way, but that was with the older openOB version. Hope that's somewhat helpful at least! Richard. *From:* Phil Biehl <fylbeall(a)gmail.com> *Sent:* Thursday, 16 July 2020 03:19 *To:* openob-users(a)lists.talkunafraid.co.uk *Subject:* [openob-users] Prerequisites I am having difficulty getting prerequisites loaded on a raspberry pi 4. I’ve fixed this problem before but I cant seem to remember how I did it! Help please. As an update for you all, I gave up on the Behringer UCA202s and its inherent mono problem have substituted a HifiBerry DAC+ ADC Pro for the input to the transmitter side, and a DAC+ Pro XLR for the output at the receiver side. Thanks pi@OpenOB-TX:~ $ sudo apt-get install python-gst0.10 python-setuptools gstreamer0.10-plugins-base gstreamer0.10-plugins-bad gstreamer0.10-plugins-good gstreamer0.10-plugins-ugly gstreamer0.10-ffmpeg gstreamer0.10-tools python-gobject python-gobject-2 gstreamer0.10-alsa python-argparse Reading package lists... Done Building dependency tree Reading state information... Done Package python-gst0.10 is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source Package gstreamer0.10-plugins-good is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source Package gstreamer0.10-plugins-bad is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source However the following packages replace it:   gstreamer0.10-plugins-base Package gstreamer0.10-plugins-ugly is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source Package gstreamer0.10-ffmpeg is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source E: Package 'python-gst0.10' has no installation candidate E: Package 'gstreamer0.10-plugins-bad' has no installation candidate E: Package 'gstreamer0.10-plugins-good' has no installation candidate E: Package 'gstreamer0.10-plugins-ugly' has no installation candidate E: Package 'gstreamer0.10-ffmpeg' has no installation candidate pi@OpenOB-TX:~ $ _______________________________________________ openob-users mailing list -- openob-users(a)lists.talkunafraid.co.uk To unsubscribe send an email to openob-users-leave(a)lists.talkunafraid.co.uk